GB/T 18170-2008
ActiveSpecifications of amusement rides battery car category
电池车类游艺机通用技术条件
Catalogue
前言 → 1 范围 → 2 规范性引用文件 → 3 总则 → 4 基本设计规定 → 5 传动系统 → 6 电气 → 7 轨道和车道 → 8 车辆 → 9 安全设施 → 10 控制装置 → 11 试验方法 → 12 检验规则 → 附录A Foreword → 1 Scope → 2 Normative References → 3 General → 4 Basic Design Requirements → 5 Transmission System → 6 Electrical → 7 Track and Lane → 8 Vehicle → 9 Safety Facilities → 10 Control Devices → 11 Test Methods → 12 Inspection Rules → Annex A
Scope
This standard specifies the general technical conditions and technical requirements for amusement rides of battery car category. This standard applies to the design, manufacture, installation, modification, maintenance, test, inspection and use management of battery car category amusement rides (hereinafter referred to as battery cars).
本标准规定了电池车类游艺机通用技术条件和技术要求。本标准适用于电池车类游艺机的设计、制造、安装、改造、维修、试验、检验和使用管理（以下简称电池车）。
Normative References
Keywords
Application Summary AI generated
Designers, manufacturers, installers, modifiers, maintenance teams, testing agencies, inspection departments, and operators of battery car amusement rides use this standard. They apply it to ensure the safety, reliability, and technical consistency of battery cars. This standard matters because it provides unified technical specifications for the entire lifecycle of battery cars, helping to prevent accidents and protect rider safety.
电池车类游艺机的设计人员、制造厂家、安装公司、改造单位、维修团队、试验机构、检验部门和使用管理者都需要遵循本标准。他们用这个标准来确保电池车的安全性、可靠性和技术一致性。这个标准很重要，因为它为电池车的全生命周期提供了统一的技术规范，有助于防止事故、保障游客安全。
AI Summary AI generated
This standard specifies general technical conditions and requirements for battery car category amusement rides, covering design, manufacture, installation, modification, maintenance, test, inspection, and use management. It requires a minimum whole-machine service life of 4,000 hours and compliance with GB 8408-2008 safety code. Compared to the previous version, new chapters on transmission system, electrical, track and lane, vehicle, safety facilities, and control devices were added. Safety signs, test methods, and inspection rules were clarified, with major defects such as starting slip, abnormal transmission, and safety handle failure explicitly defined.
本标准规定了电池车类游艺机的通用技术条件和技术要求，适用于其设计、制造、安装、改造、维修、试验、检验和使用管理。标准要求电池车整机使用寿命不小于4000小时，设计需符合GB 8408-2008安全规范。相比旧版，新增了传动系统、电气、轨道和车道、车辆、安全设施、控制装置等章节，并明确了安全标志、试验方法和检验规则，特别是对起动打滑、传动异常、安全把手失效等重大缺陷进行了规定。
Key Sentences extracted from text
本标准规定了电池车类游艺机通用技术条件和技术要求。
电池车的设计、制造、安装、改造、维修、试验、检验和使用管理，应执行本标准并符合GB 8408-2008的规定。
电池车的设计、制造、安装应保证人身安全。
电池车的设计应确定其整机及主要部件设计使用寿命，整机使用寿命不小于4 000 h。
电池车的设计应符合GB 8408-2008的规定。
This standard specifies the general technical conditions and technical requirements for amusement rides of battery car category.
The design, manufacture, installation, modification, maintenance, test, inspection and use management of battery cars shall comply with this standard and the provisions of GB 8408-2008.
The design, manufacture and installation of battery cars shall ensure personal safety.
The design of battery cars shall determine the design service life of the whole machine and main parts, and the service life of the whole machine shall not be less than 4 000 h.
The design of battery cars shall comply with the provisions of GB 8408-2008.
Standard Timeline
Changes from replaced version:
- 在第1章范围中，明确了电池车类游艺机的设计、制造、安装、改造、维修、试验、检验和使用管理
- 增加了第5章传动系统、第6章电气、第7章轨道和车道、第8章车辆、第9章安全设施、第10章控制装置以及附录A
- 在第4章中增加了设计要求的各载荷和设计计算应考虑的刚度、刚度计算、疲劳强度等
- 在第8章中增加了安全带的种类
- 在第9章中增加了安全标志的设置
- 在第11章试验方法中去掉了应力测量
- 在第12章检验规则中增加了三类产品重大缺陷：起动时有明显打滑现象，传动机构运转不正常，车辆运转时有异常的振动、发热、声响及卡阻现象；安全把手损坏、失效；安全带损坏、失效；去掉了主电路无短路保护
- 增加了附录A（规范性附录）关于主要部件、重要的轴、销轴和重要焊缝的确定
- In Chapter 1 Scope, clarified the design, manufacture, installation, modification, maintenance, test, inspection and use management of battery car category amusement rides
- Added Chapter 5 Transmission System, Chapter 6 Electrical, Chapter 7 Track and Lane, Chapter 8 Vehicle, Chapter 9 Safety Facilities, Chapter 10 Control Devices, and Annex A
- In Chapter 4, added load requirements for design and considerations for stiffness, stiffness calculation, fatigue strength, etc.
- In Chapter 8, added types of safety belts
- In Chapter 9, added setting of safety signs
- In Chapter 11 Test Methods, removed stress measurement
- In Chapter 12 Inspection Rules, added three categories of major product defects: obvious slipping during start-up, abnormal transmission operation, abnormal vibration, heating, noise and jamming during vehicle operation; safety handle damaged or failed; safety belt damaged or failed; removed no short-circuit protection for main circuit
- Added Annex A (normative) on determination of main parts, important shafts, pins and important welds