GB/T 18167-2008
ActiveSpecification of amusement rides shooting category
光电打靶类游艺机通用技术条件
Catalogue
前言 → 1 范围 → 2 规范性引用文件 → 3 总则 → 4 基本设计规定 → 5 传动系统 → 6 电气与控制系统 → 7 制造与安装 → 8 试验方法 → 9 检验规则 Foreword → 1 Scope → 2 Normative References → 3 General → 4 Basic Design Requirements → 5 Transmission System → 6 Electrical and Control System → 7 Manufacturing and Installation → 8 Test Methods → 9 Inspection Rules
Scope
This standard specifies the technical conditions and technical requirements for amusement rides of the photoelectric shooting category. This standard applies to the design, manufacture, installation, modification, maintenance, testing, inspection and use management of photoelectric shooting amusement rides (hereinafter referred to as photoelectric shooting).
本标准规定了光电打靶类游艺机的技术条件和技术要求。本标准适用于光电打靶类游艺机的设计、制造、安装、改造、维修、试验、检验和使用管理（以下简称光电打靶）。
Normative References
Keywords
Application Summary AI generated
Designers, manufacturers, installers, modifiers, maintenance personnel, inspection bodies, and amusement park operators use this standard. They apply it to ensure that photoelectric shooting rides meet safety and technical requirements throughout their lifecycle. This standard matters because it harmonizes technical specifications and protects both riders and operators.
光电打靶类游艺机的设计人员、制造厂家、安装公司、改造单位、维修人员、检验机构以及游乐场运营方都会使用这个标准。他们用它来确保设备从设计到使用的全过程符合安全和技术要求。这个标准很重要，因为它统一了技术规范，保障了游客和操作人员的安全。
AI Summary AI generated
GB/T 18167-2008 'Specification of amusement rides shooting category' replaces GB 18167-2000 and specifies technical requirements for the design, manufacture, installation, modification, maintenance, testing, inspection and use management of photoelectric shooting amusement rides. New chapters on transmission systems, electrical and control systems, and manufacturing/installation are added, with enhanced requirements for design calculations and power supply. The overall machine service life must be at least 30,000 hours, designs must ensure passenger safety, and transmission systems must operate without anomalies.
GB/T 18167-2008《光电打靶类游艺机通用技术条件》替代了GB 18167-2000，规定了光电打靶类游艺机的设计、制造、安装、改造、维修、试验、检验和使用管理的技术要求。标准新增了传动系统、电气与控制系统、制造与安装等章节，并强化了设计计算和供电系统要求。整机使用寿命不小于30000小时，设计需保证游客安全，传动系统运行应无异常。
Key Sentences extracted from text
本标准规定了光电打靶类游艺机的技术条件和技术要求。
光电打靶的设计、制造、安装、改造、维修、试验、检验和使用管理，应执行GB 8408-2008和本标准的有关规定。
光电打靶的设计应正确，结构合理；应保证游客安全。
光电打靶应规定其机械、电气等主要部件设计寿命，整机使用寿命不小于30000h。
传动系统的设计应保证零部件可靠，整机运行时不允许有异常响声、振动、冲击、发热、声响及卡阻现象。
This standard specifies the technical conditions and technical requirements for amusement rides of the photoelectric shooting category.
The design, manufacture, installation, modification, maintenance, testing, inspection and use management of photoelectric shooting shall comply with the relevant provisions of GB 8408-2008 and this standard.
The design of photoelectric shooting shall be correct and structurally reasonable; the safety of passengers shall be ensured.
The design life of main components such as mechanical and electrical parts shall be specified, and the overall service life of the machine shall not be less than 30,000 h.
The design of the transmission system shall ensure reliable components, and no abnormal noise, vibration, impact, heating, sound or jamming is allowed during operation of the whole machine.
Standard Timeline
Changes from replaced version:
- 在范围中明确了光电打靶类游艺机的设计、制造、安装、改造、维修、试验、检验和使用管理
- 增加了第5章传动系统、第6章电气与控制系统、第7章制造与安装
- 将原技术要求修改为第4章基本设计规定，增加了设计计算及对程序的设计要求
- 在第6章电气与控制系统中主要增加和修改了对供电系统的要求
- 在第9章检验规则中调整了部分产品缺陷内容
- Clarified the scope to include design, manufacture, installation, modification, maintenance, testing, inspection and use management of photoelectric shooting amusement rides
- Added Chapter 5 Transmission System, Chapter 6 Electrical and Control System, and Chapter 7 Manufacturing and Installation
- Changed the original technical requirements to Chapter 4 Basic Design Requirements, adding design calculation and program design requirements
- Mainly added and revised requirements for the power supply system in Chapter 6 Electrical and Control System
- Adjusted some product defect contents in Chapter 9 Inspection Rules