JB/T 4067.3-2011
AbolishedEngraving machines—Part 3: Types and parameters
刻模铣床 第3部分：型式与参数
Catalogue
前言 → 1 范围 → 2 规范性引用文件 → 3 型式与参数 → 3.1 型式 → 3.2 参数 Foreword → 1 Scope → 2 Normative References → 3 Types and parameters → 3.1 Types → 3.2 Parameters
Scope
This part of JB/T 4067 specifies the types, main parameters and connection dimension parameters of engraving machines. This part applies to flat engraving machines with pantograph center distance of 235 mm to 400 mm and three-dimensional engraving machines with pantograph center distance of 350 mm to 460 mm.
JB/T 4067 的本部分规定了刻模铣床的型式、主参数和连接尺寸参数。本部分适用于缩放仪中心距为235 mm～400 mm 的平面刻模铣床及缩放仪中心距为350 mm～460 mm的立体刻模铣床。
Normative References
Keywords
Application Summary AI generated
Manufacturers and users of engraving machines use this standard to define machine types and key parameters such as pantograph center distance, table dimensions, and spindle taper. It ensures uniformity and interchangeability of basic specifications across different producers, facilitating selection and application.
刻模铣床的制造商和用户使用该标准来确定机床的型式和关键参数，如缩放仪中心距、工作台尺寸和主轴锥孔等。它确保了不同厂家生产的刻模铣床在基本规格上具有统一性和互换性，便于选型和使用。
AI Summary AI generated
This standard specifies the types (three-dimensional and flat) and main parameters of engraving machines, including pantograph center distance, worktable dimensions, and spindle taper. It applies to flat engraving machines with pantograph center distance 235-400 mm and three-dimensional machines with 350-460 mm. The standard references GB/T 158 and GB/T 321 to ensure parameter selection consistency.
本标准规定了刻模铣床的型式（立体和平面）及主要参数，包括缩放仪中心距、工作台尺寸、主轴锥孔等。适用于缩放仪中心距235-400mm的平面刻模铣床和350-460mm的立体刻模铣床。标准还引用了GB/T 158和GB/T 321，确保参数选择的规范性。
Key Sentences extracted from text
JB/T 4067 的本部分规定了刻模铣床的型式、主参数和连接尺寸参数。
本部分适用于缩放仪中心距为235 mm～400 mm 的平面刻模铣床及缩放仪中心距为350 mm～460 mm的立体刻模铣床。
刻模铣床的型式分为立体刻模铣床和平面刻模铣床，如图1 和图2 所示。
机床的主运动为主轴的回转运动，仿形加工时，缩放仪围绕靠模作纵向、横向、垂向的进给运动；普通铣削时，缩放仪固定，工作台手动作纵向、横向、垂向进给运动。
工作台的长度、宽度，允许以表列数值为基数，在GB/T 321—2005 的R40 数系的前、后各四项中选取。
This part of JB/T 4067 specifies the types, main parameters and connection dimension parameters of engraving machines.
This part applies to flat engraving machines with pantograph center distance of 235 mm to 400 mm and three-dimensional engraving machines with pantograph center distance of 350 mm to 460 mm.
The types of engraving machines are divided into three-dimensional engraving machines and flat engraving machines, as shown in Figure 1 and Figure 2.
The main motion of the machine is the rotary motion of the spindle; during copying, the pantograph performs longitudinal, transverse, and vertical feed movements around the template; during ordinary milling, the pantograph is fixed and the worktable is manually fed longitudinally, transversely, and vertically.
The length and width of the worktable may be selected from the four items before and after the R40 series of GB/T 321—2005, based on the values listed in the table.
Standard Timeline
Changes from replaced version:
- 将标准名称“刻模铣床 参数”改为“刻模铣床 第3部分：型式与参数”
- 增加了第2章“规范性引用文件”
- 立体刻模铣床的主参数缩放仪中心距由“350 mm～450 mm”改为“350 mm～460 mm”
- Changed the standard name from 'Engraving machines—Parameters' to 'Engraving machines—Part 3: Types and parameters'
- Added Chapter 2 'Normative References'
- Changed the main parameter pantograph center distance of three-dimensional engraving machines from '350 mm～450 mm' to '350 mm～460 mm'