JB/T 3364.3-2011
ActiveCircular sawing machine—Part 3: Specifications
圆锯床 第3部分：技术条件
Catalogue
前言 → 1 范围 → 2 规范性引用文件 → 3 一般要求 → 4 附件和工具 → 5 加工和装配质量 → 6 机床空运转试验 → 7 机床负荷试验 → 8 机床精度检验 → 9 制造厂的保证 Foreword → 1 Scope → 2 Normative References → 3 General Requirements → 4 Accessories and Tools → 5 Machining and Assembly Quality → 6 No-Load Test of the Machine → 7 Load Test of the Machine → 8 Accuracy Inspection of the Machine → 9 Manufacturer's Guarantee
Scope
This part of JB/T 3364 specifies the technical conditions for the manufacture and acceptance of circular sawing machines. This part applies to horizontal, swing, and vertical circular sawing machines with a maximum circular saw blade diameter of 315 mm to 2 000 mm. Circular sawing machines with a maximum circular saw blade diameter less than 315 mm or greater than 2 000 mm may use this part as a reference.
JB/T 3364 的本部分规定了圆锯床的制造与验收的技术条件。本部分适用于最大圆锯片直径为315 mm～2 000 mm 的卧式圆锯床、摆式圆锯床和立式圆锯床。最大圆锯片直径小于315 mm 或大于2 000 mm 的圆锯床可参照本部分使用。
Normative References
Keywords
Application Summary AI generated
Manufacturers and inspectors of circular sawing machines use this standard to ensure consistent manufacturing quality and acceptance criteria. It provides comprehensive technical conditions covering general requirements, load tests, and accuracy inspections for various types of circular sawing machines. This standard is important because it establishes clear technical indicators and test methods to guarantee machine performance reliability and safety.
圆锯床的制造商和检验人员使用本标准来确保机床的制造质量和验收一致性。它规定了从一般要求到负荷试验和精度检验的全面技术条件，适用于多种类型的圆锯床。该标准通过明确的技术指标和试验方法，保障了机床的性能可靠性和安全性。
AI Summary AI generated
This standard JB/T 3364.3—2011 specifies technical conditions for manufacturing and acceptance of circular sawing machines, applicable to horizontal, swing, and vertical types with blade diameters from 315 mm to 2000 mm. It covers general requirements, accessories, machining and assembly quality, no-load and load tests, accuracy inspection, and manufacturer's guarantee. Key requirements include aging treatment of critical parts, spindle bearing temperature limits (60°C for sliding, 70°C for rolling), noise not exceeding 85 dB(A), and load tests verifying torque and productivity. The standard also mandates a 1-year warranty for design or manufacturing defects.
本标准JB/T 3364.3—2011规定了圆锯床的制造与验收技术条件，适用于最大锯片直径315mm至2000mm的卧式、摆式和立式圆锯床。内容涵盖一般要求、附件工具、加工装配质量、空运转和负荷试验、精度检验及制造厂保证。关键要求包括重要零件时效处理、主轴轴承温度限制（滑动轴承60°C，滚动轴承70°C）、噪声不超过85dB(A)，以及负荷试验中扭矩和生产率验证。标准还明确了制造厂对设计、制造缺陷的1年保修责任。
Key Sentences extracted from text
JB/T 3364 的本部分规定了圆锯床的制造与验收的技术条件。
本部分适用于最大圆锯片直径为315 mm～2 000 mm 的卧式圆锯床、摆式圆锯床和立式圆锯床。
床身、立柱、主传动箱、支座、工作台等重要零件，应进行时效处理。
在空运转条件下，机床的噪声声压级不得超过85 dB（A）。
在符合机床的运输、保管、安装、调试、维修和遵守使用规程的条件下，用户自收货之日起1年内，因设计、制造缺陷或包装质量不良等原因造成机床损坏或其不能正常使用时，制造厂应负责包修、包退、包换。
This part of JB/T 3364 specifies the technical conditions for the manufacture and acceptance of circular sawing machines.
This part applies to horizontal, swing, and vertical circular sawing machines with a maximum circular saw blade diameter of 315 mm to 2 000 mm.
Important parts such as bed, column, main drive box, support, and worktable shall undergo aging treatment.
Under no-load conditions, the noise sound pressure level of the machine shall not exceed 85 dB(A).
Under the conditions of conforming to the machine's transportation, storage, installation, debugging, maintenance, and following the operating instructions, if the machine is damaged or cannot operate normally due to design, manufacturing defects, or poor packaging quality within 1 year from the date of receipt by the user, the manufacturer shall be responsible for repair, return, or replacement.
Standard Timeline
Changes from replaced version:
- 第1章“范围”扩大了，包括卧式圆锯床、摆式圆锯床和立式圆锯床整个圆锯床组系；增加了“最大圆锯片直径小于315 mm 或大于2 000 mm 的圆锯床可参照本部分使用”的要求。
- 在第7章“机床负荷试验”中增加了“最大生产率的试验”项目，提高了机床负荷试验要求。
- 增加了第9章“制造厂的保证”。
- Chapter 1 'Scope' has been expanded to include the entire family of circular sawing machines: horizontal, swing, and vertical; added the requirement that 'circular sawing machines with a maximum circular saw blade diameter less than 315 mm or greater than 2 000 mm may use this part as a reference.'
- In Chapter 7 'Load Test of the Machine', the item 'maximum productivity test' has been added, raising the requirements for machine load testing.
- Chapter 9 'Manufacturer's Guarantee' has been added.