JC/T 608-2011
ActiveCement bulk loader for truck
汽车用水泥散装机
Catalogue
前言 → 1 范围 → 2 规范性引用文件 → 3 型式、标记和基本参数 → 4 技术要求 → 5 试验方法 → 6 检验规则 → 7 标志、包装、运输和贮存 Foreword → 1 Scope → 2 Normative References → 3 Type, Marking and Basic Parameters → 4 Technical Requirements → 5 Test Methods → 6 Inspection Rules → 7 Marking, Packaging, Transport and Storage
Scope
This standard specifies the type, marking and basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transport and storage of cement bulk loader for truck (hereinafter referred to as bulk loader). This standard applies to cement bulk loader for truck.
本标准规定了汽车用水泥散装机(以下简称散装机)的型式、标记和基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于汽车用水泥散装机。
Normative References
Keywords
Application Summary AI generated
Cement manufacturers and logistics companies use this standard to design and procure cement bulk loaders for trucks. It ensures the loader can efficiently and safely fill tankers, preventing dust leakage and material waste. By providing unified technical requirements and inspection rules, it guarantees equipment reliability and loading accuracy, which is crucial for standardizing bulk cement transport.
水泥生产企业和物流公司使用该标准来设计和采购汽车用水泥散装机。该标准确保散装机能够高效、安全地将水泥装入罐车，防止粉尘泄漏和物料浪费。它通过统一的技术要求和检验规则，保障设备可靠性和装车精度，对水泥散装运输的规范化至关重要。
AI Summary AI generated
This standard specifies the type, marking, basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transport and storage of cement bulk loaders for trucks. The products are classified into mobile and fixed types, each with silo-side and silo-bottom subtypes. Technical requirements include loading capacity, material level control, sealing to prevent dust, painting and rust prevention. Test methods cover no-load and load trial runs, as well as loading capacity measurement. Inspection includes factory and type inspection with judgment rules. The standard also covers marking, packaging, transport and storage to ensure equipment reliability and operational safety.
本标准规定了汽车用水泥散装机的型式、标记、基本参数、技术要求、试验方法、检验规则及标志包装等。产品分为移动式和固定式，每种又分库侧式和库底式。技术要求包括装车能力、料位控制、密封防尘、涂漆防锈等。试验方法涵盖空载和负载试运转及装车能力测定。检验分出厂和型式检验，并规定了判定规则。标准还涉及标志、包装、运输和贮存要求，确保设备可靠性和使用安全。
Key Sentences extracted from text
本标准规定了汽车用水泥散装机(以下简称散装机)的型式、标记和基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。
散装机装车的水泥含水量不应大于1％，温度不应高于120℃。
散装机配料位器应能可靠地控制装车的料面位置，不应有溢料现象。
卸料装置、装料装置、收尘接口连接件应密封，防止粉尘外溢。
负载试运转合格后方可进行装车能力测定。
This standard specifies the type, marking and basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transport and storage of cement bulk loader for truck (hereinafter referred to as bulk loader).
The moisture content of cement loaded by the bulk loader shall not be greater than 1%, and the temperature shall not be higher than 120°C.
The material level indicator of the bulk loader shall reliably control the material surface position during loading, and there shall be no overflow phenomenon.
The discharge device, loading device, and dust collection interface connectors shall be sealed to prevent dust leakage.
The loading capacity test shall be carried out only after the load trial run is qualified.
Standard Timeline
Changes from replaced version:
- 修改了标准名称，从'水泥散装设备汽车用水泥散装机'改为'汽车用水泥散装机'
- 增加了规范性引用文件GB/T 191、GB/T 1184—1996
- 第3章名称从'产品分类'改为'型式、标记与基本参数'
- 修改了'型式'和'标记'的内容
- 修改了'基本参数'
- 增加了非机械加工的线性尺寸公差和形位公差要求
- 增加了对铸铁件、铸钢件、铸钢件交货以及装车水泥含水量和温度的要求
- 增加了对收尘接口连接件密封的要求
- 删除了对吸尘管、下料管使用寿命的要求
- 修改了装车能力测定中'结果计算'
- 修改了型式检验
- 增加判定规则
- 增加了包装标志
- 增加了运输要求
- Modified the standard name from 'Cement bulk loading equipment - Cement bulk loader for truck' to 'Cement bulk loader for truck'
- Added normative references GB/T 191, GB/T 1184—1996
- Chapter 3 name changed from 'Product classification' to 'Type, marking and basic parameters'
- Modified 'Type' and 'Marking'
- Modified 'Basic parameters'
- Added requirements for linear dimension tolerances and geometric tolerances for non-machined parts
- Added requirements for cast iron parts, cast steel parts, delivery of cast steel parts, and moisture content and temperature of loaded cement
- Added requirements for sealing of dust collection interface connectors
- Deleted requirements for service life of suction pipe and discharge pipe
- Modified 'Result calculation' in loading capacity measurement
- Modified type inspection
- Added judgment rules
- Added packaging marking
- Added transport requirements