JC/T 607-2011
ActiveCement bulk loader for train
火车用水泥散装机
Catalogue
前言 → 1 范围 → 2 规范性引用文件 → 3 型式、标记和基本参数 → 4 技术要求 → 5 试验方法 → 6 检验规则 → 7 标志、包装、运输和贮存 Foreword → 1 Scope → 2 Normative References → 3 Type, Marking and Basic Parameters → 4 Technical Requirements → 5 Test Methods → 6 Inspection Rules → 7 Marking, Packaging, Transport and Storage
Scope
This standard specifies the type, marking and basic parameters, technical requirements, test methods, inspection rules, as well as marking, packaging, transport and storage of cement bulk loader for train (hereinafter referred to as bulk loader). This standard applies to cement bulk loader for train.
本标准规定了火车用水泥散装机(以下简称散装机)的型式，标记和基本参数、技术要求、试验方法、检验规则以及标志、包装、运输和贮存等。本标准适用于火车用水泥散装机。
Normative References
Keywords
Application Summary AI generated
This standard is used by cement manufacturers and railway transport departments to regulate the design, manufacturing, and inspection of bulk loading equipment for cement trains. It ensures efficient and safe loading of cement into railcars, preventing dust pollution and improving loading efficiency. The standard is crucial for maintaining quality and environmental compliance in bulk cement transport.
火车用水泥散装机标准主要被水泥生产企业和铁路运输部门使用，用于规范火车装载水泥的散装设备的设计、制造和检验。该标准确保散装机能够高效、安全地完成水泥装车作业，防止粉尘污染，提高装车效率。它对于保障水泥散装运输的质量和环保要求具有重要意义。
AI Summary AI generated
This standard specifies the type, marking, basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transport, and storage of cement bulk loaders for trains. The loader comes in two types: hard pipe and flexible pipe, designed for loading cement into railcars. Key requirements include reliable material level control to prevent overflow, no leakage at interfaces, and strict tolerances for assembly and installation. Tests include no-load and load trial runs, with inspection divided into factory and type tests. Replacing the 1995 version, this standard adds improvements such as dust collection interfaces and packaging markings.
本标准规定了火车用水泥散装机的型式、标记、基本参数、技术要求、试验方法、检验规则及标志、包装、运输和贮存。散装机分为硬料管式和软料管式两种，适用于火车水泥装车。标准要求散装机料位器可靠控制料面，防止溢料；各接口无泄漏；装配和安装需满足严格公差和密封要求。试验包括空载和负载试运转，检验分出厂和型式检验。该标准替代了1995年版，增加了多项技术改进，如收尘接口要求和包装标志。
Key Sentences extracted from text
本标准规定了火车用水泥散装机(以下简称散装机)的型式，标记和基本参数、技术要求、试验方法、检验规则以及标志、包装、运输和贮存等。
散装机分为风送斜槽下料硬料管式(代号为Y)、软料管式(代号为R)两种型式。
散装机料位器应能可靠地控制装车的料面位置，不应有溢料现象。
各接口处均不应有泄漏现象。
负载试运转应达到4.2的规定。
This standard specifies the type, marking and basic parameters, technical requirements, test methods, inspection rules, as well as marking, packaging, transport and storage of cement bulk loader for train (hereinafter referred to as bulk loader).
The bulk loader is divided into two types: air conveying chute discharge hard pipe type (code Y) and flexible pipe type (code R).
The material level indicator of the bulk loader should reliably control the material level position during loading, and there should be no overflow phenomenon.
There should be no leakage at all interfaces.
The load trial operation should meet the requirements of 4.2.
Standard Timeline
Changes from replaced version:
- 标准名称改为'火车用水泥散装机'
- 增加了规范性引用文件GB/T 191、GB/T 1184-1996
- 用JC/T 820-1988(1996)替换原引用标准ZB 092 002
- 第3章名称由'产品分类'改为'型式、标记和基本参数'并作相应修改
- 增加了非机械加工的线性尺寸公差和形位公差要求
- 增加了收尘接口要求
- 删除了对吸尘管、下料管使用寿命的规定
- 修改了'结果计算'
- 修改了型式试验的规定
- 增加判定规则
- 增加了包装标志要求
- 增加了运输要求
- 修改了'贮存'的要求
- Standard name changed to 'Cement bulk loader for train'
- Added normative references GB/T 191, GB/T 1184-1996
- Replaced original reference standard ZB 092 002 with JC/T 820-1988(1996)
- Chapter 3 name changed from 'Product classification' to 'Type, marking and basic parameters' with corresponding modifications
- Added requirements for linear dimension tolerances and geometric tolerances for non-machined parts
- Added dust collection interface requirements
- Deleted provisions on service life of suction pipe and discharge pipe
- Modified 'Result calculation'
- Modified provisions for type test
- Added judgment rules
- Added packaging marking requirements
- Added transport requirements
- Modified 'Storage' requirements