JB/T 53198-1999
Rolling Type Capping Machine - Product Quality Grading (Internal Use)
滚压式封口机 产品质量分等（内部使用）
Catalogue
前言 → 1 范围 → 2 引用标准 → 3 产品质量等级 → 4 试验方法 → 5 抽样与评定办法 → 附录A 主要零件 Foreword → 1 Scope → 2 Normative References → 3 Product Quality Grades → 4 Test Methods → 5 Sampling and Evaluation Methods → Appendix A Main Parts
Scope
This standard specifies the product quality grades, test methods, and sampling and evaluation methods for rolling type capping machines. This standard is applicable to the product quality grading of rolling type capping machines that comply with the provisions of JB/T 7549.3-1994 "Rolling Type Capping Machine".
本标准规定了滚压式封口机的产品质量等级，试验方法和抽样与评定办法。 本标准适用于符合JB/T 7549.3—1994《滚压式封口机》规定的滚压式封口机的产品质量分等。
Normative References
Keywords
Application Summary AI generated
Manufacturers, quality inspection agencies, and users of rolling type capping machines use this standard. It is employed to evaluate and grade the product quality of these machines into three levels: qualified, first-class, and premium. This standard matters because it establishes key performance indicators such as productivity, vacuum degree, and bottle breakage rate, ensuring consistent quality and providing a benchmark for production and acceptance.
该标准由滚压式封口机的制造企业、质量检验机构以及用户使用。用于对滚压式封口机进行产品质量等级评定，包括合格品、一等品和优等品三个等级。该标准通过规定生产率、真空度、破瓶率等关键指标，确保封口机的性能和质量，为生产和使用提供统一的质量评判依据。
AI Summary AI generated
This standard JB/T 53198-1999 specifies the product quality grading requirements for rolling type capping machines, including three grades: qualified, first-class, and premium. It lists key indicators such as productivity, post-capping vacuum degree, bottle breakage rate, vacuum drop value, fault downtime, noise, and main parts quality level, along with corresponding grade requirements. The standard also defines test methods (per JB/T 7549.3) and sampling/evaluation procedures (based on GB/T 2828). It applies to rolling type capping machines conforming to JB/T 7549.3, providing a unified basis for quality control and grade determination.
本标准JB/T 53198-1999规定了滚压式封口机的产品质量分等要求，包括合格品、一等品和优等品三个等级。标准详细列出了生产率、封口后真空度、破瓶率、真空下降值、故障停机时间、噪声及主要零件质量水平等关键指标及其对应等级要求。同时规定了试验方法（按JB/T 7549.3执行）和抽样评定办法（基于GB/T 2828）。该标准适用于符合JB/T 7549.3的滚压式封口机，为产品质量控制和等级判定提供了统一依据。
Key Sentences extracted from text
本标准规定了滚压式封口机的产品质量等级，试验方法和抽样与评定办法。
产品质量等级应符合表1 的规定。
封口后瓶内真空度 ≥40 ≥45 ≥50
破 瓶 率 % ≤0.4 ≤0.3 ≤0.2
优等品：检查考核主要项目必须全部达到优等品水平，一般项目中允许有一项达到一等品水平，其余均达到优等品水平。
This standard specifies the product quality grades, test methods, and sampling and evaluation methods for rolling type capping machines.
Product quality grades shall comply with the provisions of Table 1.
Vacuum degree in bottle after capping ≥40 ≥45 ≥50
Bottle breakage rate % ≤0.4 ≤0.3 ≤0.2
Premium product: All main items inspected must reach the premium product level; among general items, one item may reach the first-class product level, and the rest must reach the premium product level.
Standard Timeline
Changes from replaced version:
- 对原标准作了编辑性修改，主要技术内容没有变化。
- Editorial modifications were made to the original standard, with no changes to the main technical content.