JB/T 11646-2013
ActiveSpecial equipment for semi-dry desulfurization device - Fluid trough
半干法脱硫装置专用设备 流化槽
Catalogue
前言 → 1 范围 → 2 规范性引用文件 → 3 术语和定义 → 4 技术要求 → 4.1 基本要求 → 4.2 主要零部件要求 → 4.3 装配要求 → 5 试验方法与检验规则 → 5.1 出厂检验 → 5.2 现场安装检验 → 6 标志、包装、运输和贮存 → 附录A (资料性附录) 典型的流化槽布置型式、结构示意图 Foreword → 1 Scope → 2 Normative References → 3 Terms and Definitions → 4 Technical Requirements → 4.1 Basic Requirements → 4.2 Requirements for Main Components → 4.3 Assembly Requirements → 5 Test Methods and Inspection Rules → 5.1 Factory Inspection → 5.2 On-site Installation Inspection → 6 Marking, Packaging, Transport and Storage → Annex A (Informative) Typical Layout and Structural Diagram of Fluid Trough
Scope
This standard specifies the terms and definitions, technical requirements, test methods, inspection rules, marking, packaging, transport and storage of fluid troughs for semi-dry desulfurization devices. This standard applies to fluid troughs for semi-dry desulfurization devices.
本标准规定了半干法脱硫装置配套流化槽的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于半干法脱硫装置配套的流化槽。
Normative References
Keywords
Application Summary AI generated
This standard is used by desulfurization equipment manufacturers, environmental engineering companies, and power plants to design and manufacture fluid troughs for semi-dry desulfurization devices. It ensures the reliability and efficiency of fluid troughs in conveying dry powdered materials, which is critical for the overall performance of the desulfurization system.
该标准由脱硫设备制造商、环保工程公司和电厂使用，用于设计和制造半干法脱硫装置中的流化槽。它确保了流化槽在输送干燥粉状物料时的可靠性和效率，对提高脱硫系统的整体性能至关重要。
AI Summary AI generated
This standard JB/T 11646-2013 specifies technical requirements for fluid troughs in semi-dry desulfurization devices, including definitions, component requirements, assembly, test methods, and inspection rules. Fluid troughs use fluidization to convey dry powdered materials, classified as air slides or fluidized flat troughs. It also covers marking, packaging, transport, and storage, referencing multiple national and industry standards to ensure equipment quality and installation consistency.
本标准JB/T 11646-2013规定了半干法脱硫装置中流化槽的技术要求，包括术语定义、零部件要求、装配要求、试验方法和检验规则。流化槽利用流态化原理输送干燥粉状物料，分为空气斜槽和流化平槽。标准还涉及标志、包装、运输和贮存，并引用了多项相关国家标准和行业标准，确保设备质量和安装一致性。
Key Sentences extracted from text
本标准规定了半干法脱硫装置配套流化槽的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。
利用流态化输送原理，达到干燥粉状物料水平输送的装置。
沿其输送方向布置成一定的斜度的流化槽称为空气输送斜槽。
流化槽主要由下槽体、透气层、上槽体、压紧钢丝网、紧固件五部分组成。
本标准适用于半干法脱硫装置配套的流化槽。
This standard specifies the terms and definitions, technical requirements, test methods, inspection rules, marking, packaging, transport and storage of fluid troughs for semi-dry desulfurization devices.
A device that utilizes fluidization conveying principles to achieve horizontal conveying of dry powdered materials.
A fluid trough arranged at a certain slope along its conveying direction is called an air conveying slide.
The fluid trough mainly consists of five parts: lower trough body, permeable layer, upper trough body, compression wire mesh, and fasteners.
This standard applies to fluid troughs for semi-dry desulfurization devices.